|
|
Realization of educational problem based on experimental apparatus with cam mechanism
Tomeček, Vojtěch ; Vrbka, Martin (referee) ; Vaverka, Michal (advisor)
Bachelor's thesis is focused on solving educational problem based on experimental apparatus with cam mechanism. The task of the educational problem is to teach students to analyse kinematic quantities of cam followers. The thesis contains general discourse on the topic of cam mechanisms and basic terms definition. This is followed by putting the device into service, eliminating its particular imperfections, analysis of kinematic quantities of various combinations of available cams and followers and definition of methodics of the educational problem. The educational problem itself follows the presentation and commentary of gained results. At last some recommendations for the future modifications of the experimental apparatus are given followed by foreshadow of its eventual future usage.
|
|
|
Experimental Analysis of Kinematic Quantities on Cam Mechanism
Komenda, Lukáš ; Dočkal, Aleš (referee) ; Zimmerman, Martin (advisor)
This diploma thesis deals with creation of a laboratory task related with analysis of kinematic quantities on cam machanism. A new measuring chain was created as a part of the new laboratory task for analysis of kinematic quantities with use of sensors and signal processing by software LabVIEW. The concept of the laboratory task on a experimental machine was based on knowledge gained from Current State of Knowledge where basic principles of laboratory training and utilization of cam mechanisms in learning were described.
|
|
|
Measurement unit for sports analysis with inertial sensors
Dugas, Martin ; Brablc, Martin (referee) ; Kumpán, Pavel (advisor)
Master's thesis is dealing with desgin of a measuring unit incorporating inertial sensors, used for analysis in canoe sprint. Data from a three-axis accelerometer and a three-axis gyroscope were combined using an extended Kalman filter, yielding speed, roll, pitch and yaw of the boat and stroke rate. Calculated values were verified by a GPS. Furthermore, parameters describing dynamic behaviour of the system were identified, allowing an inclusion of dynamic quantities like force and power into the analysis.
|
|
|
Simulation of phenomena in switchgears
Daševič, Ladislav ; Vávra, Zdeněk (referee) ; Valenta, Jiří (advisor)
Aim of the thesis is to explain the issue of forces acting in circuit breaker caused by magnetic fields induced by short-circuit current. This thesis is focused on force affecting in concrete system of a circuit breaker. The given circuit breaker is made by OEZ Letohrad, the type Modeion BD250. In the thesis the way of creating 3-D model is shown for the purpose of creating numeric simulation by ANSYS 11. The next approach of the thesis is the description of applicating the results for DC and AC current calculations. The noted calculation is made in the programme MATLAB 6.5. The solutions are mentioned at calculations both in the graphic form and numeric specifications. Visualisation was made by using GIF graphic system animation. The individual pictures processing was done in the programme UNLEAD GIF ANIMATOR 5.
|
|
|
The device for measuring of camshafts timings
Jozíf, Lukáš ; Mazal, Pavel (referee) ; Mazůrek, Ivan (advisor)
Bachelor’s thesis is focused on constructional concept of device for measuring of camshafts timing and its wear-out. After short introduction and definitions of basic concepts there are problems of cams design analyzed and overview of the commercially offered devices is mentioned. Next part focuses on construction of the proper device including design documentation. Procedure of measuring with the device and example of some data evaluation is described. In the conclusion I evaluated constructional and economic aspect the whole concept.
|
|
|
Measurement unit for sports analysis with inertial sensors
Dugas, Martin ; Brablc, Martin (referee) ; Kumpán, Pavel (advisor)
Master's thesis is dealing with desgin of a measuring unit incorporating inertial sensors, used for analysis in canoe sprint. Data from a three-axis accelerometer and a three-axis gyroscope were combined using an extended Kalman filter, yielding speed, roll, pitch and yaw of the boat and stroke rate. Calculated values were verified by a GPS. Furthermore, parameters describing dynamic behaviour of the system were identified, allowing an inclusion of dynamic quantities like force and power into the analysis.
|
|
|
Experimental Analysis of Kinematic Quantities on Cam Mechanism
Komenda, Lukáš ; Dočkal, Aleš (referee) ; Zimmerman, Martin (advisor)
This diploma thesis deals with creation of a laboratory task related with analysis of kinematic quantities on cam machanism. A new measuring chain was created as a part of the new laboratory task for analysis of kinematic quantities with use of sensors and signal processing by software LabVIEW. The concept of the laboratory task on a experimental machine was based on knowledge gained from Current State of Knowledge where basic principles of laboratory training and utilization of cam mechanisms in learning were described.
|
|
|
Simulation of phenomena in switchgears
Daševič, Ladislav ; Vávra, Zdeněk (referee) ; Valenta, Jiří (advisor)
Aim of the thesis is to explain the issue of forces acting in circuit breaker caused by magnetic fields induced by short-circuit current. This thesis is focused on force affecting in concrete system of a circuit breaker. The given circuit breaker is made by OEZ Letohrad, the type Modeion BD250. In the thesis the way of creating 3-D model is shown for the purpose of creating numeric simulation by ANSYS 11. The next approach of the thesis is the description of applicating the results for DC and AC current calculations. The noted calculation is made in the programme MATLAB 6.5. The solutions are mentioned at calculations both in the graphic form and numeric specifications. Visualisation was made by using GIF graphic system animation. The individual pictures processing was done in the programme UNLEAD GIF ANIMATOR 5.
|
|
|
Realization of educational problem based on experimental apparatus with cam mechanism
Tomeček, Vojtěch ; Vrbka, Martin (referee) ; Vaverka, Michal (advisor)
Bachelor's thesis is focused on solving educational problem based on experimental apparatus with cam mechanism. The task of the educational problem is to teach students to analyse kinematic quantities of cam followers. The thesis contains general discourse on the topic of cam mechanisms and basic terms definition. This is followed by putting the device into service, eliminating its particular imperfections, analysis of kinematic quantities of various combinations of available cams and followers and definition of methodics of the educational problem. The educational problem itself follows the presentation and commentary of gained results. At last some recommendations for the future modifications of the experimental apparatus are given followed by foreshadow of its eventual future usage.
|
|
|
The device for measuring of camshafts timings
Jozíf, Lukáš ; Mazal, Pavel (referee) ; Mazůrek, Ivan (advisor)
Bachelor’s thesis is focused on constructional concept of device for measuring of camshafts timing and its wear-out. After short introduction and definitions of basic concepts there are problems of cams design analyzed and overview of the commercially offered devices is mentioned. Next part focuses on construction of the proper device including design documentation. Procedure of measuring with the device and example of some data evaluation is described. In the conclusion I evaluated constructional and economic aspect the whole concept.
|
guest ::
